< Back

What to Do If You Have NO Hot Water

If you have some hot water, or the water is just not hot enough, or some other problem, see the Troubleshooting section. The guide below is for a new water heater installation where you have NO HOT WATER AT ALL.

If you have no hot water after installing a new water heater, the most likely reasons are (1) no electric power or (2) the upper heating element was burned out during installation (dry fire).

The information on this web site is supplemental to the printed instructions that came with your water heater. To reduce the risk of property damage, serious injury or death, read and follow all labels on the water heater and the safety instructions in the printed owner's manual.


Step 1: Tools and Supplies

Hand dishwashing soap
thumbnail1thumbnail2thumbnail3
  • Hand dishwashing soap

  • Element wrench

  • Garden hose and bucket (optional)

  • Multimeter

  • Non-contact circuit tester

  • Paper towels or shop rags

  • 1/4" nut driver and/or screwdriver

  • New upper element

Step 2: Turn Power OFF

Locate the water heater's circuit breaker and turn it OFF (or remove the circuit's fuses).
thumbnail1thumbnail2
  • Locate the water heater's circuit breaker and turn it OFF (or remove the circuit's fuses).

  • WARNING! Before working on the water heater, use a non-contact circuit tester or volt meter to make sure power is off. Working on an energized appliance can cause electrical burns, electrocution or death.

Step 3: Open Electrical Junction Box Cover

Open the electrical junction box access panel on the old water heater.
thumbnail1thumbnail2thumbnail3
  • Open the electrical junction box access panel on the old water heater.

  • Your access panel may look different and may use a different type of screw.

Step 4: Check for Electrical Power

Using a non-contact circuit tester, check the power wires to make certain the power is off.
thumbnail1thumbnail2
  • Using a non-contact circuit tester, check the power wires to make certain the power is off.

  • WARNING! Working on an energized circuit can result in severe injury or death from electrical shock. Check wires with a volt meter or circuit tester to make sure power is off.

Step 5: Replace the Junction Box Cover

Replace the junction box cover.
thumbnail1thumbnail2
  • Replace the junction box cover.

  • WARNING! Be sure all covers are secured to reduce the risk of fire and electric shock.

Step 6: Remove Upper Heating Element Cover

Remove the upper heating element cover.
thumbnail1thumbnail2thumbnail3
  • Remove the upper heating element cover.

Step 7: Move Insulation Out of the Way

Move the insulation out of the way (tuck the insulation under the water heater's jacket).
thumbnail1thumbnail2thumbnail3
  • Move the insulation out of the way (tuck the insulation under the water heater's jacket).

  • WARNING! Working on an energized circuit can result in severe injury or death from electrical shock. Check wires with a volt meter or circuit tester to make sure power is off.

Step 8: Remove Plastic Protector

Remove plastic protector.
thumbnail1thumbnail2thumbnail3
  • Remove plastic protector.

Step 9: Turn Power ON

Turn the power ON.
thumbnail1thumbnail2
  • Turn the power ON.

  • WARNING! Working near an energized circuit can result in severe injury or death from electrical shock.

Step 10: Set the Multimeter to AC Volts

See the water heater's data plate for the correct voltage.
thumbnail1thumbnail2thumbnail3
  • See the water heater's data plate for the correct voltage.

  • Set the multimeter to read AC Volts.

Step 11: Check Voltage

<strong>WARNING! Working near an energized circuit can result in severe injury or death from electrical shock.</strong>
thumbnail1thumbnail2thumbnail3
  • WARNING! Working near an energized circuit can result in severe injury or death from electrical shock.

  • Check the voltage at the top two screws of the upper thermostat.

  • Compare your reading to the voltage listed on the data plate.

  • Choose how to continue below.

  • If the voltage does not match the requirements on the water heater's data plate (usually 240 volts AC), there is likely a problem with the home's electrical wiring. Contact an electrician or other qualified person.